Cyberbullying: Effect of emergency perception on the helping tendencies of bystanders

The effect of the emergency perception of bystanders of cyberbullying victims on helping behaviors is often neglected in research on cyberbullying. In this study, we explored the influence of this cognitive factor on cyber-bystanders’ helping tendencies as well as elucidated possible underlying processes. The results of two studies were reported. In Study 1, 150 undergraduates read a true case of a girl experiencing cyberbullying. The results indicated that when the participants perceived the victim’s situation to be more critical (i.e., higher emergency perception), their helping tendencies were stronger, partly through increased state empathy followed by feelings of responsibility to help. In Study 2, we randomly assigned 300 undergraduates to two groups. The low emergency group read the same cyberbullying case as Study 1, whereas the cyberbullying case read by the high emergency group contained additional emergency information of the victim. The results indicated that the high emergency group expressed stronger helping tendencies than did the low emergency group. This effect was caused by a stronger perception that the victim was in an emergency situation, which not only strengthened the participants’ helping tendencies directly but also indirectly through increasing their state empathy and feelings of responsibility to help.     

Optimal Design of Novel Electromagnetic-Ring Active Balancing Actuator with Radial Excitation

Imbalance vibration is a typical failure mode of rotational machines and has significant negative effects on the effii-ciency,accuracy,and service life of equipment.To automatically reduce the imbalance vibration during the opera-tional process,different types of active balancing actuators have been designed and widely applied in actual produc-tion.However,the existing electromagnetic-ring active balancing actuator is designed based on an axial excitation structure which can cause structural instability and has low electromagnetic driving efficiency.In this paper,a novel radial excitation structure and the working principle of an electromagnetic-ring active balancing actuator with a combined driving strategy are presented in detail.Then,based on a finite element model,the performance param-eters of the actuator are analyzed,and reasonable design parameters are obtained.Self-locking torque measurements and comparative static and dynamic experiments are performed to validate the self-locking torque and driving effi-ciency of the actuator.The results indicate that this novel active balancing actuator has sufficient self-locking torque,achieves normal step rotation at 2000 r/min,and reduces the driving voltage by 12.5％.The proposed novel balancing actuator using radial excitation and a combination of permanent magnets and soft-iron blocks has improved electro-magnetic efficiency and a more stable and compact structure.     

改进的CAGAN在虚拟试衣中的应用

针对CAGAN（Conditional Analogy GAN）换衣后效果模糊，在目标衣服与原始衣服长短不一致时效果一般，相对目标衣服保留过少的细节等问题做了相关研究并对CAGAN进行了改进，提出了新的虚拟试衣方式。经过改进的CAGAN生成一个粗糙的结果，由该结果得到目标衣服穿在模特身上改变形状后的mask，接下来利用mask对目标衣服进行变形，综合变形的衣服和第一步的结果便得到最终的试衣图像。实验结果表明，该方法解决了前面存在的问题，而且取得了非常好的效果。     

Failure and fragmentation of ceramic target with varying geometric configuration under ballistic impact

The failure and fragmentation of monolithic bare alumina 99.5% ceramic target and energy dissipation of steel 4340 projectile have been studied in a series of ballistic experiments carried out, with the incidence velocities in a range, 122–290 m/s. The velocity drop and energy dissipation increased with incidence velocity for 10 mm thick target with damage zone extended upon the whole area of rear face at higher velocities. The ballistic results obtained with the 10 mm thick target have been compared with the ballistic performance of the 5 mm thick target used in a previous study to explore the effects of target thickness on the failure mechanism. A model for the residual velocity of projectile after perforation of the single layered ceramic target has been developed based on the Lambert Jonas model by using the experimental data available for 5 mm and 10 mm thick alumina 99.5% target against 10.9 mm projectile. The residual velocities and damage patterns were reproduced with a reasonable amount of accuracy by a three-dimensional finite element model developed on commercial ABAQUS/CAE. The effect of obliquity and projectile diameter to target thickness ratio (D/T) on ballistic performance has been determined by the numerical simulation model with impact velocity in a range of 300–500 m/s. A spatial variation of ejected fragments velocity at different time steps was plotted to develop a velocity profile for the ceramic fragments coming out of the target. A semi-empirical model has been proposed for residual velocity after perforation of a monolithic ceramic target, relating to the incidence velocity and projectile diameter to target thickness ratio. The monolithic ceramic targets have been investigated for a comparative assessment of energy dissipation by the ceramic layer to eventually design an efficient front layer of a ceramic based composite armour in future studies.     

Mathematical law of size effect on the flexural property of ceramics

Brittle materials generally exhibit size effects, and the mechanical properties of these materials degrade significantly with an increase in size. However, the mathematical law governing the attenuation degree of mechanical properties with the increase in size is still unknown. In this study, maximum loads of differently sized ceramic test strips were subjected to three point bending tests under two working conditions of equal spans and span amplifications, respectively. Subsequently, the theoretical maximum loads of materials were calculated using the finite element method (FEM). By calculating the difference between the calculated values and the actual maximum loads, the attenuation of mechanical properties of ceramic samples were observed. The results show that the theoretical mechanical properties and the performance attenuation caused by the size effect tend to increase according to the following equation: y=ax³+bx²+cx+d. Therefore, mechanical properties and performance attenuation of any sample exhibiting a size within the experimental range can be predicted by a mathematical law, which was obtained through mechanical tests results of four samples with different sizes. The obtained mathematical law holds great significance for predicting the mechanical properties of materials under size effects.     

Effects of TGO growth on the stress distribution and evolution of three-dimensional cylindrical thermal barrier coatings based on finite element simulations

Based on the ultrasonic C-scan results of 8YSZ coatings after thermal cycles, three-dimensional cylindrical numerical simulations of the physical geometry model of the thermal barrier coating (TBC) sinusoidal surfaces were conducted with finite elements to estimate the stress distribution and evolution law of the top coat (TC)/bond coat (BC) interface, including the centre and edge of the specimen affected by the dynamic growth of the thermally grown oxide (TGO). The results show that when a layer of TGO is grown on the TC/BC interface, compressive stress is uniformly distributed on the TGO interface, and the stress value decreases as a function of the TGO layer thickness. When the thickness of the TGO exceeds a certain value, the compressive stress of all parts of the interface gradually changes to tensile stress; meanwhile, the edges of the model affected by the crest and trough effects of the wave are reflected in the radial and circumferential directions, especially along the axial direction, with alternating concentrated tensile and compressive stresses. TGO growth imposes a minor influence on the magnitude and distributions of the radial and circumferential stresses at the BC interface. The linear elasticity, creep, fatigue, and stress accumulation effects of each layer of TBCs in each thermal cycle were fully considered in this model. The model not only interprets the crest and trough effects of the TC/BC surface interface during the growth of TGO, but also interprets the effects of the core and edge of the cylindrical model, further revealing the reason for which the core and edge of the TBC will most likely form cracks.     

基于LBSN动态异构网络的时间感知兴趣点推荐

随着基于位置社交网络(Location-Based Social Network,LBSN)的快速发展,兴趣点(Point-Of-Interest,POI)推荐可以帮助人们发现有趣的并吸引人的位置。针对签到数据的稀疏性和用户兴趣的动态性等挑战性问题,提出了基于LBSN动态异构网络的时间感知兴趣点推荐算法。在LBSN异构网络模式中增加会话节点类型。通过动态元路径,在用户和兴趣点语义关系之间有效地融入时间信息、位置信息和社交信息等。设置了用户-兴趣点之间的动态元路径集,并提出了动态路径实例的偏好度计算方法。采用矩阵分解模型对不同动态偏好矩阵进行矩阵分解。根据不同动态元路径的用户特征矩阵和兴趣点特征矩阵,获取用户在目标时间访问兴趣点的推荐列表。实验结果表明,与其他兴趣点推荐方法相比,所提方法在兴趣点推荐精确度上取得了较好的推荐结果,具有良好的应用前景。     

密文策略属性加密中的撤销控制方案

在云环境下使用数据共享功能时，由于云环境的复杂性，需要对数据进行安全保护和访问控制，这就要求使用加密机制。基于密文策略属性的加密（CP-ABE）是当前广泛使用的加密机制，它可以根据用户的属性来设置访问权限，任何具有合格访问权限的用户都可以访问数据。然而云是一个动态环境，有时可能只允许具有访问权限用户中的一部分用户访问数据，这就需要用户权限的撤销机制。然而，在CP-ABE中，访问权撤销或用户撤销是一个冗长且代价高昂的事件。所提出方案根据对CP-ABE流程的改进，在原密文中嵌入了可灵活控制的用户个人秘密，使得用户权限撤销时既不要求使用新访问策略的用户撤销数据，也不要求对数据进行重新加密，大幅减少撤销时的计算成本。与知名CP-ABE撤销方案对比，所提出方案的计算成本更低且具有良好的安全性。     

基于改进的Random Subspace的客户投诉分类方法

电信业的客户投诉不断增多而又亟待高效处理。针对电信客户投诉数据的特点，提出了一种面向高维数据的改进的集成学习分类方法。该方法综合考虑客户投诉中的文本信息及客户通讯状态信息，基于Random Subspace方法，以支持向量机（Support Vector Machine，SVM）为基分类器，采用证据推理（Evidential Reasoning，ER）规则为一种新的集成策略，构造分类模型对电信客户投诉进行分类。所提模型和方法在某电信公司客户投诉数据上进行了验证，实验结果显示该方法能够显著提高客户投诉分类的准确率和投诉处理效率。     

适用于无线体域网的动态口令认证协议

无线体域网中传输的是与生命高度相关的敏感数据，身份认证是信息安全保护的第一道防线。现有的基于人体生物信息的身份认证方案存在信息难提取、偶然性大和误差性大的问题，基于传统密码学的认证方案需较大计算资源和能量消耗，并不适用于无线体域网环境。为此，在动态口令和非对称加密机制基础上，提出一种适用于无线体域网的动态口令双向认证轻量协议，并对其进行形式化分析。通过理论证明、SVO逻辑推理及SPIN模型检测得出：该协议满足双向认证，且能够抵御重放攻击、伪装攻击、拒绝服务器攻击和口令离线攻击，具有较高安全性。